View T370HW03VD_1563986.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 1 / 29 model name: t370hw03 vd issue date : 2009/09/02 ( )preliminary specifications ( )final specifications customer signature date auo date approved by _________________________________ approval by pm director frank hsu ____________________________________ reviewed by rd director eugene cc chen ____________________________________ reviewed by project leader: jason ____________________________________ note prepared by pm: shuzi cheng _ __________________________________ _ www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 2 / 29 contents no contents record of revisions 1 general description 2 absolute maximum ratings 3 electrical specification 3-1 electriacl characteristics 3-2 interface connections 3-3 signal timing specification 3-4 signal timing waveform 3-5 color input data reference 3-6 power sequence 3-7 backlight specification 4 optical specification 5 mechanical characteristics 6 reliability test items 7 international standard 7-1 safety 7-2 emc 8 packing 8-1 definition of label 8-2 packing methods 8-3 pallet and shipment information 9 precaution 9-1 mounting precautions 9-2 operating precautions 9-3 electrostatic discharge control 9-4 precautions for strong light exposure 9-5 storage 9-6 handling precautions for protect film www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 3 / 29 record of revision version date page description 0.0 2009/09/2 first release www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 4 / 29 1. general description this specification applies to the 37.0 inch color tft-lcd module t370hw03 vd. this lcd module has a tft active matrix type liquid crystal panel 1920*1080 pixels, and diagonal size of 37.0 inch. this module supports 1920*1080 hdtv mode (non-interlace). each pixel is divided into red, green and blue sub-pixels or dots which are arranged in vertical stripes. gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot. the t370hw03 vd has been designed to apply the 8-bit 2 channel lvds interface method. it is intended to support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very important. the t370hw03 vd model is rohs verified which can be distinguished on panel label. * general information items specification unit note active screen size 37.01 inch display area 819.36 (h) x 460.89(v) mm outline dimension 877(h) x 514.6(v) x 54.3(d) mm with inverter driver element a-si tft active matrix display colors 8 bit, 16.7m colors number of pixels 1920 x 1080 pixel pixel pitch 0.42675(h) x 0.42675(w) mm pixel arrangement rgb vertical stripe display operation mode normally black surface treatment anti-glare, 3h haze = 11 www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 5 / 29 2. absolute maximum ratings the followings are maximum values which, if exceeded, may cause faulty operation or damage to the unit item symbol min max unit conditions logic/lcd drive voltage vcc -0.3 14 [volt] note 1 input voltage of signal vin -0.3 4 [volt] note 1 operating temperature top 0 +50 [ o c] note 2 operating humidity hop 10 90 [%rh] note 2 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 10 90 [%rh] note 2 panel surface temperature pst 65 [ o c] note 3 note 1: duration:50 msec. note 2 : maximum wet-bulb should be 39 and no condensation. the relative humidity must not exceed 90% non-condensing at temperatures of 40 or less. at temperatures greater than 40 , the wet bulb temperature must not exceed 39 . note 3: surface temperature is measured at 50 dry condition www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 6 / 29 3. electrical specification the t370hw03 vd requires two power inputs. one is employed to power the lcd electronics and to drive the tft array and liquid crystal. the second input power for the blu, is to power inverter. (inv) 3.1 electrical characteristics value parameter symbol min. typ. max unit note lcd power supply input voltage v dd 10.8 12 13.2 v dc 1 power supply input current i dd - 1 1.2 a 2 power consumption p c - 12 14.4 watt 2 inrush current i rush - - 4 a 3 differential input high threshold voltage v th -- -- +100 4 4 differential input low threshold voltage v tl -100 -- -- 4 4 lvds interface input common mode voltage v icm 1.10 1.25 1.40 v dc 4 cmos interface input high threshold voltage v ih (high) 2.4 3.3 v dc input low threshold voltage v il (low) 0 0.9 v dc backlight power consumpti on p bl 104 110 116 watt life time 50000 -- hours 8 note : 1. the ripple voltage should be controlled under 10% of v cc 2. test condition: (1) v dd = 12.0v (2) fv = type timing, 60hz, 120hz or other (3) f clk = max freq. (4) temperature = 25 (5) test pattern : white pattern 3. measurement condition : rising time = 400us www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 7 / 29

s 4. v icm = 1.25v 5. do not attach a conducting tape to lamp connecting wire. if the lamp wire attach to conducting tape, tft-lcd module have a low luminance and the inverter has abnormal action because leakage current occurs between lamp wire and conducting tape. 6. the relative humidity must not exceed 80% non-condensing at temperatures of 40 or less. at temperatures greater than 40 , the wet bulb temper ature must not exceed 39 . when operate at low temperatures, the brightness of ccfl will drop and the life time of ccfl will be reduced. 7. specified values are for a single lamp only which is aligned horizontally. the lifetime is defined as the time which luminance of the lamp is 50% compared to its original value. [operating condition: continuous operating at ta = 252 ] www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 8 / 29 3.2 interface connections lcd connector: p2 187059-51221 mating connector: \ www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 9 / 29 lvds option = high/open ns

! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! "#$%&'()*$))))))))))))))))))))))))))))))))'##$+,)*$)))))))))))))))))))))))))))$,)*$)))) "#$%&'()*$))))))))))))))))))))))))))))))))'##$+,)*$)))))))))))))))))))))))))))$,)*$)))) "#$%&'()*$))))))))))))))))))))))))))))))))'##$+,)*$)))))))))))))))))))))))))))$,)*$)))) "#$%&'()*$))))))))))))))))))))))))))))))))'##$+,)*$)))))))))))))))))))))))))))$,)*$)))) note: x = 1, 2, 3, 4 lvds option = low jeida

! ! ! ! ! ! ! !

! ! ! !

"#$%&'()*$))))))))))))))))))))))))))))))))'##$+,)*$)))))))))))))))))))))))))))$,)*$)))) "#$%&'()*$))))))))))))))))))))))))))))))))'##$+,)*$)))))))))))))))))))))))))))$,)*$)))) "#$%&'()*$))))))))))))))))))))))))))))))))'##$+,)*$)))))))))))))))))))))))))))$,)*$)))) "#$%&'()*$))))))))))))))))))))))))))))))))'##$+,)*$)))))))))))))))))))))))))))$,)*$)))) note: x = 1, 2, 3, 4 www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 10 / 29 3.3 signal timing specification this is the signal timing required at the input of the user connector. all of the interface signal timing should be satisfied with the following specifications for its proper operation. signal item symbol min. typ. max unit period tv 1090 1125 1480 th active tdisp (v) 1080 th vertical section blanking tblk (v) 10 45 400 th period th 1030 1100 1325 tc lk active tdisp (h) 960 tclk horizontal section blanking tblk (h) 70 140 365 tc lk clock frequency fclk=1/tclk 50 74.25 82 mhz vertical frequency frequency fv 47 60 63 hz horizontal frequency frequency fh 60 67.5 73 khz notes: (1) display position is specific by the rise of de signal only. horizontal display position is specified by the rising edge of 1 st dclk after the rise of 1 st de, is displayed on the left edge of the screen. (2)vertical display position is specified by the rise of de after a low level period equivalent to eight times of horizontal period. the 1 st data corresponding to one horizontal line after the rise of 1 st de is displayed at the top line of screen. (3)if a period of de high is less than 1920 dclk or less than 1080 lines, the rest of the screen displays black. (4)the display position does not fit to the screen if a per iod of de high and the effective data period do not synchronize with each other. www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 11 / 29 3.4 signal timing waveforms - .&(/0%1 20%1 % ) 3,3 &+$ +%3&.)3,3 +%3&.)3,3 &+$ &+$ &+$ &+$ &+$
4 "&$) ! "&$) "&$) "&$) "&$) "&$)
"&$) "&$) +%3&.)3,3 +%3&.)3,3 "&$) "&$) "&$) "&$) "&$)
"&$) "&$) ! "&$) 5 "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$)
"&$) "&$) +%3&.)3,3 +%3&.)3,3 "&$) "&$) "&$) "&$)
- .&(/0-1 20-1 ) ) ) ) / / / / & & & & $ $ $ $ )&+$ )&+$ )&+$ )&+$ www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 12 / 29 3.5 color input data reference the brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter the color. the table below provides a reference for color versus data input. color data reference input color data red msb lsb green msb lsb blue msb lsb color r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ---- red(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 r red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 ---- green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 g green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ---- blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 b blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 13 / 29 3.6 power sequence for lcd value parameter min. typ. max. units t1 0.4 --- 30 ms t2 0.1 --- 50 ms t3 300 --- --- ms t4 10 --- --- ms t5 0.1 --- 50 ms t6 --- --- 300 ms t7 500 --- --- ms note: (1) t4=0 : concern for residual pattern before blu turn off. (2) t6 : voltage of vdd must decay smoothly after power-off. (customer system decide this value) www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 14 / 29 3.7 backlight specification (inverter type) the backlight unit contains 14-i type ccfls (cold cathode fluorescent lamp) 3.7.1 electrical specification ( note 1 : dimming ratio= 100% (max) ta=255 , turn on for 45minutes note 2: measurement condition rising time = 20ms (vddb : 10%~90%); note 3: less than10% dimming control is functional well and no backlight shutdown happened spec item symbol condition min typ max unit note 1 input voltage vddb - 22.5 24 26.4 vdc - 2 input current i ddb vddb=24v - 4.58 4.81 adc 1 3 input power p ddb vddb=24v 104 110 116 w 1 4 inrush current i rush vddb=24v - - 7.2 adc 2 on 2 - 5 - 5 on/off control voltage v blon off vddb=24v 0 - 0.8 vdc - 6 on/off control current i blon vddb=24v - - 1.5 ma - max 0 - 3.3 vdc - 7 dimming control voltage v_dim min vddb=24v - 0 - vdc - 8 dimming control current i_dim vddb=24v - - 2 madc - 9 internal dimming ratio dim_r vddb=24v 20 100 % 3 max vddb=24v 2 - 3.3 - 10 external pwm control voltage v_epwm min vddb=24v 0 - 0.8 vdc - 11 external pwm control current i_epwm vddb=24v - - 2 madc - 12 external pwm duty ratio d_epwm vddb=24v 5 - 100 % 3 13 external pwm frequency f_epwm vddb=24v 140 180 240 hz - www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 15 / 29 3.7.2 input pin assignment inverter connector: ci0114m1hrl-nh (cvilux) (note*) if external pwm function includes 10% dimming ratio. judge condition as below: (1) backlight module must be lighted on normally. (2) all protection function must work normally. (3) uniformity and flicker could not be guaranteed pin symbol description 1 vddb operating voltage supply, +24v dc regulated 2 vddb operating voltage supply, +24v dc regulated 3 vddb operating voltage supply, +24v dc regulated 4 vddb operating voltage supply, +24v dc regulated 5 vddb operating voltage supply, +24v dc regulated 6 blgnd ground and current return 7 blgnd ground and current return 8 blgnd ground and current return 9 blgnd ground and current return 10 blgnd ground and current return 11 det blu status detection: normal : 0~0.8v ; abnormal : open collector 12 vblon blu on-off control: high/open (3.3v~5.5v) : bl on ; low (0~0.8v/gnd) : bl off 13 vdim(**) internal pwm (0~3.3v for 10~100% duty, open for 100%) < nc ; at external pwm mode> 14 pdim(*) external pwm (5%~100% duty, open for 100%) < nc ; at internal pwm mode> www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 16 / 29 3.7.3 power sequence for inverter www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 17 / 29 4. optical specification optical characteristics are determined after the unit has been on and stable for approximately 45 minutes in a dark environment at 25c. the values specified are at an approximate distance 50cm from the lcd surface at a viewing angle of and equal to 0. fig.1 presents additional information concerning the measurement equipment and method. values parameter symbol min. typ. max unit notes contrast ratio cr 3000 4000 1 surface luminance (white) l wh 360 450 cd/m 2 2 luminance variation white(9p) -- -- 1.3 3 response time (g to g) t -- 6.5 -- ms 4 color gamut ntsc 72 % color coordinates red r x 0.640 r y 0.330 green g x 0.29 g y 0.6 blue b x 0.144 b y 0.060 white w x 0.280 w y typ.-0.03 0.290 typ.+0.03 viewing angle 5 x axis, right( =0) r -- 89 -- degree x axis, left( =180) l -- 89 -- degree y axis, up( =90) u -- 89 -- degree y axis, down ( =270) d -- 89 -- degree note: sr3 or equivalent www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 18 / 29 1. contrast ratio (cr) is defined mathematically as: surface luminance of l on5 contrast ratio= surface luminance of l off5 2. surface luminance is luminance value at point 5 across the lcd surface 50cm from the surface with all pixels displaying white. from more information see fig 2. when lamp current i h = 11ma. l wh =lon5 where lon5 is the luminance with all pixels displaying white at center 5 location. 3. the variation in surface luminance, white is defined (center of screen) as: white(9p) = maximum(l on1 , l on2 ,,l on9 )/ minimum(l on1 , l on2 ,l on9 ) 4. response time is the average time required for display transition by switching the input signal for five luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on f v =60hz to optimize. target measured response time 0% 25% 50% 75% 100% 0% 0% to 25% 0% to 50% 0% to 75% 0% to 100% 25% 25% to 0% 25% to 50% 25% to 75% 25% to 100% 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100% 75% 75% to 0% 75% to 25% 75% to 50% 75% to 100% start 100% 100% to 0% 100% to 25% 100% to 50% 100% to 75% 4. viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the lcd surface. for more information see fig4. fig. 2 luminance 1 2 3 4 5 6 7 8 h v h/6 h/2 v/2 v/6 www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 19 / 29 fig.3 response time the response time is defined as the following figure and shall be measured by switching the input signal for any level of grey(bright) and any level of gray(dark). any level of gray (bright) any level of gray (dark) any level of gray (bright) t (r) 0%, 25%, 50%, 75%, 100% photodetector output time t (f) 0%, 25%, 50%, 75%, 100% 0%, 25%, 50%, 75%, 100% fig.4 viewing angle www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 20 / 29 5. mechanical characteristics the contents provide general mechanical characteristics for the model t420hw06 v2. in addition the figures in the next page are detailed mechanical drawing of the lcd. horizontal 877.0 mm vertical 514.6mm outline dimension depth 54.3 mm(with inverter) horizontal 828 mm bezel opening vertical 469.8 mm horizontal 819.36 mm active display area vertical 460.89 mm weight 7000 g (typ.) surface treatment anti-glare, 3h www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 21 / 29 front view (tbd) www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 22 / 29 back view (tbd) www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 23 / 29 6. reliability test items test item qty condition 1 high temperature storage test 3 60 , 300hrs 2 low temperature storage test 3 -20 , 300hrs 3 high temperature operation test 3 50 , 300hrs 4 low temperature operation test 3 -5 , 300hrs 5 vibration test (non-operation) 3 wave form: random vibration level: 1.5g rms bandwidth: 10-300hz, duration: x, y, z 30min one time each direction 6 shock test (non-operation) 3 shock level: 50g waveform: half since wave, 11ms direction: x, y, z, one time each direction 7 vibration test (with carton) 5 random wave (1.5g rms, 10-200hz) 30mins/ per each x,y,z axes 8 drop test (with carton) 5 height: 30.5m 1 corner, 3 edges, 6 surfaces (astmd4169-i) www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 24 / 29 7. international standard 7.1 safety (1) ul 60950-1, ul 60065; standard for safety of information technology equipment including electrical business equipment. (2) iec 60950-1 : 2001, iec 60065:2001 ; standard for safety of international electrotechnical commission (3) en 60950 : 2001+a11, en 60065:2002+a1:2006; european committee for electrotechnical standardization (cenelec), european stan dard for safety of information technology equipment including electrical business equipment. 7.2 emc (1) ansi c63.4 methods of measurement of radio-noise emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. american national standards institute(ansi), 1992 (2) c.i.s.p.r limits and methods of measurement of radio interface characteristics of information technology equipment. international special committee on radio interference. (3) en 55022 limits and methods of measurement of radio interface characteristics of information technology equipment. european committee for electrotechnical standardization. (cenelec), 1998 www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 25 / 29 8. packing 8-1 definition of label: a. panel label: *xxxxxxxxxxxx -xxxx * green mark description (1) for pb free product, auo will add for identification. (2) for rohs compatible products, auo will add rohs for identification. note: the green mark will be present only when the green documents have been ready by auo internal green team. (definition of green design follows the auo green design checklist.) b. carton label:
qty : 5 au optronics xxxxx made in xxxxx manufactured xx /xx xxxxxxx model no: t370hw03 vd auo internal use week year panel unique id auo internal use factory location

www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 26 / 29 8-2 packing methods: www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 27 / 29 8-3 pallet and shipment information specification item qty. dimension weight (kg) packing remark 1 packing box 5 pcs/box 965(l)mm*375(w)mm*610(h)mm 30 2 pallet 1 1140(l)mm*980(w)mm*132(h)mm 15 3 boxes per pallet 6 boxes/pallet (by air) ; 9 boxes/pallet (by sea) 4 panels per pallet 30 pcs/pallet(by air) ; 45 boxes/pallet (by sea) pallet after packing 24 (by air) 36(by sea) 1140(l)mm*980(w)mm*1352(h)mm (by air) 1140(l)mm*980(w)mm*2094(h)mm (by sea) 285 (by air) 435 (by sea) stretch film label corner angle pet band moisture-proof film corner angle pallet www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 28 / 29 8. precautions please pay attention to the followings when you use this tft lcd module. 9-1 mounting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so that uneven force (ex. twisted stress) is not applied to module. and the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protective plate to the surface in order to protect the polarizer. transparent protective plate should have sufficient str ength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type mater ials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit broken by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothes with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth. (some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. normal-hexane is recommended for cleaning the adhesives used to attach front/ rear polarizer. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possible. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2 operating precautions (1) the device listed in the product specification sheets was designed and manufactured for tv application (2) the spike noise causes the mis-operation of circuits. it should be lower than following voltage: v=200mv(over and under shoot voltage) (3) response time depends on the temperature. (in lower temperature, it becomes longer..) (4) brightness of ccfl depends on the temperature. (in lower temperature, it becomes lower.) and in lower temperature, response time (required time that brightness is stable after turned on) becomes longer. (5) be careful for condensation at sudden temperature change. condensation makes damage to polarizer or electrical contacted parts. and after fading condensation, smear or spot will occur. (6) when fixed patterns are displayed for a long time, remnant image is likely to occur. (7) module has high frequency circuits. sufficient suppression to the electromagnetic interference shall www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net
t370hw03 vd product specification rev. 00 ? copyright auo optronics corp. 2009 all rights reserved. page 29 / 29 be done by system manufacturers. grounding and shielding methods may be important to minimize the interface. 9-3 electrostatic discharge control since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make certain that treatment persons are connected to ground through wristband etc. and dont touch interface pin directly. 9-4 precautions for strong light exposure strong light exposure causes degradation of polarizer and color filter. 9-5 storage when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the module to sunlight or fluorescent light. keep the temperature between 5 and 35 at normal humidity. (2) the polarizer surface should not come in contact with any other object. it is recommended that they be stored in the container in which they were shipped. 9-6 handling precautions for protection film (1) the protection film is attached to the bezel with a small masking tape. when the protection film is peeled off, static electricity is generated between the film and polarizer. this should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) when the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the protection film is peeled off. (3) you can remove the glue easily. when the glue remains on the bezel or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. www.braemac.co.uk sales@braemac.co.uk tel: 01925 419090 fax: 01925 419091 www..net

▲Up To Search▲

Price & Availability of T370HW03VD

	To Download T370HW03VD Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .